Integrated manufacturing of REciclable multi-material COmposites for the TRANSport sector

1. Scope

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe products2 are assembled and installed in various lengths, including long continuous lengths. These products are intended for the transport of crude oil, natural gas and hazardous liquids in the rehabilitation of existing pipelines and for new pipelines.

Note 1: Hazardous liquids are those liquids defined by the U.S. Department of Transportation in 49 CFR 195.2.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A312/A312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

A333/A333M Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness

A519 Specification for Seamless Carbon and Alloy Steel Mechanical Tubing

D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

D638 Test Method for Tensile Properties of Plastics

D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D1000 Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications

D1598 Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

D1600 Terminology for Abbreviated Terms Relating to Plastics

D1693 Test Method for Environmental Stress-Cracking of Ethylene Plastics

D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2256/D2256M Test Method for Tensile Properties of Yarns by the Single-Strand Method

D2513 Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings

D2774 Practice for Underground Installation of Thermoplastic Pressure Piping

D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

D2992 Practice for Obtaining Hydrostatic or Pressure Design Basis for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings

D3850 Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA)

D5035 Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)

F412 Terminology Relating to Plastic Piping Systems

F585 Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers

F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor

F1606 Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner

F1668 Guide for Construction Procedures for Buried Plastic Pipe

F2619/F2619M Specification for High-Density Polyethylene (PE) Line Pipe

F2620 Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings

G14Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)

PPI Standards

TR-3/2010

Other Documents

49 CFR 195 Code of Federal Regulations - Transportation of Hazardous Liquids by Pipeline

API Standards

17 J Unbonded Flexible Pipe Unbonded Flexible Pipe

ANSI Standards

B 16.5 Pipe, Flanges, and Flanged Fittings

» Code: ASTM F2896 - 11(2017)

» Committee: Subcommittee: F17.68

» More Information

« Go to Technological Watch